How To Reset Trane Thermostat? Updated 2022 Tutorial
You could have a Trane thermostat like the XL824, 850, or 1050. You might potentially be using an earlier model. Your unit may have unusual operating troubles. You may want to know how to attempt before contacting a technician for assistance. Now you might be thinking about how to reset Trane thermostat? If your Trane thermostat isn’t operating correctly, the following guide will walk you through some of the measures you may take.
Why Choose Trane Thermostat?
Trane thermostats are indeed a customer favorite for people like you and me who can’t get much of a self-set temp and all the benefits it delivers. However, suppose there are problems with the heating and cooling, and you cannot continue with your present routine. In that case, you may have to understand how to reset Trane thermostat.
If you didn’t already know. Trane provides either programmable or non-programmable thermostats. It features simple interfaces that make resetting much easier than it needs to be. Without any further ado, here are all the steps you want.
How to Reset Trane thermostat – Steps
We’ll go through how to reset Trane thermostat series of steps here.
- The first step you must do to reset a digital electrical gadget is to turn it off. As a result, you will be doing the same here to begin the procedure. Turn the Trane thermostat off.
- You must wait 30 seconds or 1 minute before turning on the Trane programmable thermostat again. You should now set the thermostat to either cool or heat.
- Now, control the temperature inside the thermostat to your liking and wait for the system to warn you by beeping when it turns on
- Stay close to the control box or circuit protection box if you can’t feel or hear the airflow.
- Find the HVAC system’s circuit. Revert to the on position if it works.
- If it was already in the “on” position, try turning it to the “off” position and afterward back to the “on” position.
- For the time being, reboot the Trane thermostat by turning it off and then again using the power button
- Control the temperature of such a Trane thermostat to finish the reset process, and you get done.
How To Reset Trane Thermostat For Pump System
It’s possible that your heating and cooling systems will lose power. In that case, you’re probably wondering if your preset preferences would get retained when you switch it back on. It loses electricity if your furnace and air conditioner gt connected to your thermostat. In that case, it will revert to default settings when power gets restored. However, suppose the heating/cooling system was formerly a heat pump system and is now a standard system. In that case, the settings are likely to malfunction.
- On the home screen, the Menu button is in the middle. Start by squeezing it. Then keep pressing the Next button until you see Customer help on the screen.
- Once you’ve done that, click the Select button. Continue pressing until you reach the Installer Setting screen. Now, once more, hit Select.
- On your screen, there must be a notification of Equipment Type. Select the option.
- When you’ve found Outdoor Select Type, hit Select one more. It will help you choose between AC and HP units. AC is usually the default, but select HP if you’ve got a heat pump. When you get finished, press the Done button.
- Then it would help if you hit the Next button, and it will bring you to the Outdoor Unit Stages page. Depending on the type of device, select the Initial phase or Step 2. Then click Done, followed by Next.
- The next screen will direct you toward the Indoor Unit Type point. It is switched to oil or gas by default. If you have got a gas furnace, you may leave it alone. But, because we’re talking about heat pump systems, odds are you’ll want to replace it, as there are electric air handlers that work with heat pumps. As a result, you’ll have to keep looking for when it reads Electric in the options instead of Gas/Oil. Click Done, then Next.
- If you guessed correctly, we should now go with Indoor Heat Stages. When you select the Select button, you may see Step 1. It is precisely what you’ve been preparing for so long. Make sure you’re happy with what you’ve chosen, then click Next. Indoor Blower Type should get shown. Select Non-variable. Then click Next.
- The Energizing Reverse Valve will now get shown. It should read, “With Cool.” Finally, click Next.
- It would be best if you now were right back to square one, but everything has changed. It would help if you now hit Done till you reach the main screen.
More on Housekeeping.tips: How to clean porcelain effectively? Read here.
How To Reset Trane Thermostat After A Power Outage?
When there is a power outage, your thermostat would likely revert to its preset settings. We worry that it will switch to a furnace or heat pump rather than the air conditioner. As a result, following a power outage, you must change the settings.
To change the settings, go to:
- Select the “Menu” button.
- Continue to press the “Next” option until you reach the “Service” menu.
- Press the “Select” button repeatedly until the “Installer Settings” window displays, then click it.
- Select “Equipment Type.”
- Choose an air conditioner.
- Click the “Done” button.
- Select “Next.”
- Select the outside unit’s serial number and press the “Next” button.
- Select the type of system you will be using.
- Finally, double-check that all of the changes you made apply to the air conditioning equipment before proceeding.
If you’re having HVAC or thermostat problems, it’s a good idea to reset the Trane air conditioner thermostat. We have given the most straightforward directions we can get so that you may complete them effortlessly and swiftly.