How To Replace Heating Element In Samsung Dryer – The Entire Process

Every day, we throw our damp clothing into the dryer and let them dry without giving it any attention. Everyone expects the machine to heat up to perform its work once the door is closed and the drying cycle begins. But what happens if the Samsung dryer fails to heat up? Also, when the components in the dryer heating element malfunction, many heating element connections can be generated, which can be harmful. So, you’re considering How To Replace Heating Element In Samsung Dryer?

This article will go over some of the most significant likely causes why your Samsung dryer won’t heat up, as well as how to repair a dryer’s heating element.

What Is A Heating Element Of A Dryer?

The heating element in the dryer works similarly to the coil in an electric heater. It comprises an uninsulated metal conductor; whenever an electric current travels through all of it, the resistance to current passage causes it to heat up. The coil will burn out if it becomes too hot.

Depending on the kind, the heating element is either behind the dryer within the dryer cabinet or beneath a panel at the rear of the dryer.

Common Causes why Dryer Heating Element is not working

Samsung is well-known for producing trustworthy, high-quality goods. However, like all the best manufacturers, Samsung dryers occasionally have issues. The most typical problem is that the dryer does not heat up, making loud, odd noises.

Dryer Heating Element

One of the most typical problems with Samsung dryers is that they do not heat up. This problem gets frequently caused by a burned-out heating element in Samsung dryers. A well-maintained dryer’s heating element should last a minimum of 15 years. On the other hand, a burnt-out heating element is commonly the fault for Samsung dryer heating issues. The element usually burns out owing to excessive wear and a failure to maintain the circulation of air clean, which puts a load on the heating element.

The heating element may get visually inspected for broken or grounded coils. The component will very probably have to get replaced if a coil breaks. A multimeter could also get used to checking for continuity in the element. When there is no continuity, the heating coils must get replaced.

Blown Thermal Fuse

An additional component offers overheating safety when it comes to household appliances that create heat. This component is known as the thermal cut-off fuse. Another typical problem with Samsung dryers is that they do not heat up due to a blown thermal fuse. The thermal fuse is a security measure that keeps the dryer from catching fire.

If somehow the dryer temperature surpasses a particular threshold, the thermal fuse blows, and the dryer stops operating. The dryer may continue to operate but without creating heat in older versions. When the temperature all around the heater component climbs over acceptable limits, the fuse burns out to safeguard the machine’s remains from destruction.

If you are interested: read how to get rid of super glue off glass easily, here.

How To Replace Heating Element In Samsung Dryer – Steps

So, how to replace heating element in Samsung dryer? Before replacing any access panels, make sure to turn off the dryer’s electricity or gas. The Samsung dryer must get disassembled to remove and replace the heating element. Although there are numerous phases, the procedure is relatively simple and can get accomplished by the typical do-it-yourselfer.

• Remove the Samsung dryer from the wall. Disconnect the dryer vent first by releasing the elastic clamp on the vent pipe with a screwdriver.
• Remove the screws on the back of the top cover using a screwdriver. Remove the top cover from the dryer and set it aside.
• Take the top covering from the controller, then detach the two guide screws and six clips from the guiding panel using a screwdriver. Remove the front knob and set it to the side after unplugging the two wires linking the panel to the dryer.
• Open the front door of the dryer and remove the filter. Remove the filter and place it to the side. Remove the screws from the front of the dryer panel.
• Loosen the four screws that connect the front plate and panel. Raise and set to the side of the front panel. The heater terminals on the heating element get removed. You can’t plug it back in the wrong way since each terminal has a unique connection.
• Take the four screws that hold the thermostat out of the drum and take the mounting screws from the back of the heating element.
• Attach the thermostat to the new heat source using the four screws.
• Place a new heating element in the drum and tighten it down.
• Replace the front plate on the dryer and use the screws to fasten it to the panel and the drum.
• Reattach the control unit’s electrical cords and snap them back into place using the clips. Fasten the unit together with the bolts and replace the knob.
• Attach the top cover to the dryer using the two screws provided.
• Try to connect the dryer vent and re-plug the dryer. Place the dryer against the wall.

So, we get done with how to replace heating element in Samsung dryer

Is It Worth Replacing Heating Element of Samsung Dryer?

However, because repairing a dryer’s heating element might be costly according to where you reside, some individuals prefer to purchase a new dryer instead. So, which route should you go? Here’s a general guideline: if the cost of fixing your current dryer is 50% less than the cost of buying a new one, you should repair it instead of buying a new one. To put it differently, if somehow the cost of repairs exceeds half the cost of the latest dryer, you really should pay the difference and purchase a new one.

Final Thought

To summarize, You must have the requisite knowledge and ability to safely and successfully repair the heating element. If you’re ever unsure about yourself, it’s advisable to seek expert assistance.