Connect with us

Housekeeping Tips

Cleaning

4 SIMPLE METHODS OF HOW TO CLEAN TILE AFTER INSTALLATION

Today we going to talk about “HOW TO CLEAN TILE AFTER INSTALLATION”. As soon as you’ve finished laying the new tile, you notice a haze on the surface. Grout haze is natural, but it might be challenging to remove. This circumstance does have a silver lining; you may already have a few choices for cleaning grouted tiles at home. According to the rule of thumb, always begin with the gentlest method and work your way up to harsher if necessary.

HOW TO CLEAN TILE AFTER INSTALLATION

After installing, the haze can be swept up using these methods.

Using a sponge, remove any excess grout from your tile once it has been applied. However, a yellowish haze can result from a small amount of grout being left behind. For a while, it may go unnoticed, especially if it is still damp. After it dries, the haze can often be seen. Behind installation, you have a few choices for sweeping ceramic tile to remove any remaining. Acting immediately is usually your best bet for getting the finest results.

Never clean tiles that are too hot. Especially those exposed to direct sunlight during the hot summer months, as the aggressive chemicals’ reaction may become more abrasive. During the summer, perform the procedure during the coolest part of the day.

When to clean: 4/5 days after grouting and within ten days
What to use: Detergent with an acidic base

#01 DRY CHEESECLOTH METHOD

HOW TO CLEAN TILE AFTER INSTALLATION

Dry cheesecloth may be all that is needed to eliminate haze. Using this procedure as soon as possible after grouting is ideal. But you must allow drying for at least 24 hours first. Haze caused by loose or readily removable grout can eliminate using this technique. After loosening the grout with a cloth, you may sweep or vacuum the floor or counter clean.

#02 TOWEL DAMPENED WITH WATER

HOW TO CLEAN TILE AFTER INSTALLATION

Cheesecloth soaked in simple water and rung out is an alternative if dry cheesecloth does not do the work. The cloth should be moist but not drenched. Haze can remove by rubbing each tile with a little elbow grease. Moisture alone can occasionally reactivate or moisten the grout on the tiles, allowing it to be readily removed. Alternatively, you might use a wet sponge.

#03 VINEGAR MIXTURE

HOW TO CLEAN TILE AFTER INSTALLATION

If water is not enough, you can use Vinegar to clean smooth porcelain or ceramic tiles. On the other hand, Vinegar should not use on any stone, slate, or other porous tile material because of its acidity. When cleaning porcelain or ceramic, mix four parts of water with one part of white Vinegar to get the best results from the Vinegar. Use a delicate cloth dipped in the vinegar mixture to clean the tiles. If the mixture is too weak, more Vinegar can be added. Remove any residual vinegar residue by rinsing the tiles with water.

#04 GROUT HAZE REMOVER

HOW TO CLEAN TILE AFTER INSTALLATION

Tile haze remover products may be necessary if the residue is still visible. Prior to applying a solution to a surface or grout, test it on an inconspicuous area to verify that it does not stain or harm the surface or grout.

In many cases, a product specifically for epoxy grout haze is required. In general, acid-based removers don’t work well with natural stone. Acidic cleaners, like Vinegar, can erode your new tile in the same way. Always use a remover that is specifically developed for the sort of tile you are dealing with.

When utilizing chemical cleansers, always work in a well-ventilated environment. Extra protection can be gained by wearing a mask and gloves. Do as instructed by the manufacturer of the cleaner. A spray or wipe application may be necessary, depending on the product. To get rid of the chemical, use only water to wash the surface.

  • Epoxy Grouting, Two-Component and Reactive

Since these grouts set quickly, even within a few minutes, this product must be removed immediately and thoroughly. Before grouting the entire floor or wall, run a cleaning test to see if the manufacturer’s recommended cleaning procedures work.

Grout can be extremely difficult, if not impossible, to remove after it has dried. Consult the company that makes the grout.

  • Non-Slip Surfaces

Non-slip surfaces are more difficult to clean because of their distinct rough, structured, or non-slip textures. Because of this, pay special attention to cleaning procedures, such as using motorized brushes with white and beige discs to clean sooner.

HOW TO CLEAN TILE AFTER INSTALLATION

HOW TO CLEAN POLISHED PORCELAIN TILE

Polished porcelain tiles give entryways and halls a striking appeal. But that stylish gloss that drew you to a polished porcelain home also shows every trace of filth and grime. While most of these are stain-resistant, you should still clean them periodically to keep them shining. Consult the tile’s maker for cleaning suggestions. If you are unsure, use a moderate, nonacidic detergent.

  1. Remove the first layer of dirt from the tile by vacuuming or sweeping it with a dust mop.
  2. Use a gentle detergent or porcelain tile cleaner to clean the floor. You can dilute household cleaners to half their normal strength if you are using them on glossy porcelain tile. Make sure to let the cleaner sit on your tile for the amount of time specified on the label, which is usually between five and 10 minutes.
  3. Rinse the tile completely with pure water after mopping to remove all of the detergents. Cleaners can leave behind a film that can discolour the tile if it is not quickly rinsed.
  4. Dry with a towel. As a result, the tile retains its aesthetic appeal and dries without streaks or stains.
Top 7 Best Selling Bathroom Shower Tile Cleaners

Conclusion

Depending on the flooring and how long the grout haze has been on the tiles, the least abrasive procedure is recommended for cleaning recently laid tiles. Continue exploring the possibilities until you find the one that gives your tiles a new lease on life.

FAQ – HOW TO CLEAN TILE AFTER INSTALLATION?

How long do you wait to clean tile after grouting?

After drying for three hours, a thin white film will likely appear on your tiles.

Will Vinegar remove grout haze?

Using a vinegar solution to remove porcelain or ceramic tile is an option. This is a no-no if you’re using slate or stone.

Will Magic Eraser remove grout haze?

It will clean it well. But use it with a moderate powder abrasive like Bon Ami or Bartender’s Friend and LOTS of water.

How do you clean porcelain tiles after installation?

Pour porcelain and ceramic tile, mix 3/4 water 1/4 vinegar. Wipe with a delicate cloth immersed in the solution, adding more Vinegar as needed. After removing, clean with normal water.

How do professionals clean grout?

A white vinegar and water solution at a 1:1 ratio. This solution is often more effective than Ph-neutral cleansers.

More in Cleaning

To Top